Chapter 14, Section 16

The Tunable Loop: The AM Listener's Secret Weapon

Part of AM Radio Facts and Trivia: The AM Broadcast Band in the USA. Updated November 16, 2026.

The cheapest, simplest piece of serious AM DX gear ever made is a coil of wire and a variable capacitor: the passive tuned loop. It has no battery, no amplifier, and, the part that surprises people, no connection to the radio at all. You set it next to a portable radio, tune its knob to the same frequency the radio is on, and weak stations rise out of the noise. Commercial versions like the venerable Select-A-Tenna and the Terk AM Advantage are 9-to-11-inch discs; the homebrew version is a wooden cross-frame with a dozen turns of wire and a 365 pF variable capacitor salvaged from a junked radio. Either way the circuit is identical, and it is the entire circuit: one coil, one capacitor.

How it sits tuning knob magnetic coupling (no wires) ferrite bar inside rotate to peak, or to null The whole schematic L ≈ 220 µH (10-15 turns on a frame) 35-365 pF f = 1 / (2π√LC) ≈ 540-1700 kHz That's it. No power. No preamp. Energy reaches the radio by induction alone.
The passive tuned loop: a parallel LC circuit on a frame, placed beside the radio. Tune the capacitor to resonance and the loop's field couples into the radio's internal ferrite bar: no wires, no power, no preamp.

Drawing 14.16-1

How a coil and a capacitor become gain. The loop and capacitor form a parallel resonant circuit. Tuned to the incoming station, the high-Q loop rings up a circulating current, and the magnetic field of that current is far stronger, right next to the loop, than the bare signal arriving from the sky. The radio's internal ferrite bar, sitting in that concentrated field, simply inhales it: inductive coupling, the same physics as a transformer with air for a core. The effect on a weak daytime signal can be startling: stations that were completely inaudible become comfortable listening. And because the boost only exists at the frequency the loop is tuned to, there's none of the overload a long random wire dumps into a small radio: the loop is an amplifier and a preselector at once, made of two parts.

The null is the real superpower. A loop hears in a figure-8: maximum off the two broadside directions, and two sharp, deep nulls. The peak is nice; the null is what DXers pay for. Rotate the loop to drop a co-channel pest, a first-adjacent splatter source, or a buzzing wall-wart into the notch (tilting the loop finds the last few dB) and a station 20 or 30 dB under the interference comes up out of the hole. Hobbyists routinely null nearby 50,000-watt locals down to a whisper to work the channel underneath. On today's crowded dial, where every former clear channel carries a stack of stations after dark (see When the Clear Channels Stopped Being Clear), the loop's null is how a listener un-stacks the pile: it's the receiving-end cousin of the directional array, doing with one rotatable coil what stations do with towers and phasors.

Old technology, never bettered. Big tuned loops were the receiving antenna of the 1920s: the elegant spiderweb and box loops that sat atop console radios before ferrite bars shrank the loop into the cabinet in the 1950s. The modern passive loop is the same idea brought back outside the box: the Select-A-Tenna has been sold essentially unchanged for decades, the Terk AM Advantage dresses the circuit up for the living room, and a homebrew frame loop built in an afternoon performs right alongside them. Practical notes: orient the loop's windings in the same plane as the radio's ferrite bar for best coupling; prove it to yourself on a weak daytime signal, because at night the radio's AGC masks the gain (the null still works fine, after dark it's the null you want anyway); and a radio with no internal ferrite bar can't couple inductively, which is why the commercial loops include a direct-connection adapter.

Chapter 14, Section 16, Part 2

How the Loopstick Inside Your Radio Works

Open almost any portable AM radio made since the 1950s and you will find the same part lying along the inside of the case: a dark gray rod, usually a few inches long, with a coil of fine wire wound around it. That is the loopstick, also called a ferrite rod antenna or ferrite bar. It is the radio’s whole antenna for the AM band. The tuned loop described above works by talking to exactly this part.

It listens to the magnetic half of the wave. A radio wave has two parts traveling together: an electric field and a magnetic field. A long wire or a whip antenna mostly picks up the electric part. The loopstick picks up the magnetic part. As the station’s magnetic field sweeps past, it passes through the coil, and a changing magnetic field passing through a coil makes a small voltage in the wire. That is the same principle as a transformer, with the radio station as the other winding.

Why the ferrite rod matters. A coil that small, wound on air, would catch almost nothing. Ferrite is a ceramic made with iron oxide that magnetic fields pass through far more easily than through air. The rod gathers the station’s magnetic field from the space around it and funnels it through the coil, so a few inches of rod can deliver a signal that DXers say can rival a wire antenna. The bigger the rod, the more field it gathers, which is why a tiny pocket radio hears far less than a big portable with a long bar.

The antenna is also the tuner. The coil on the rod is not just an antenna. It is the coil in the radio’s first tuned circuit, paired with one section of the tuning capacitor that turns when you turn the dial. Together they resonate at the station you have tuned and ignore the rest. To reach the bottom of the dial at 530 kHz with a common 365 pF tuning capacitor, the coil needs roughly 250 microhenries (that figure is arithmetic from the tuning formula, not a measured part). A second, much smaller winding of a few turns on the same rod hands the signal to the first transistor, which needs a low-impedance feed.

It points. A loopstick hears best when its side faces the station and worst when one end points straight at it. Viewed from above, its pickup pattern is a figure 8, with the two loops of the 8 off the sides of the rod and two sharp nulls off the ends. That is why turning a portable radio can make a station swell or vanish. DXers use it on purpose: point the end of the rod at an unwanted station to null it, while the station you want, coming from another direction, stays in. The nulls are much sharper than the peaks, so small turns matter. Because the 8 is symmetrical, a null cannot tell you which of the two directions along the rod the station is in.

A little less noise. Because the loopstick responds mainly to the magnetic part of the wave, DXers report that it picks up less of the electric-field noise from nearby wiring and appliances than a wire antenna does. It is not a cure for the noise described in AM Radio Noise at Home, but turning the radio to put a noise source in the null of the rod can help.

1. Catching the field station's magnetic field ferrite rod gathers the field and funnels it through the coil gray: ferrite rod copper: the coil 2. Where it hears STRONG side faces the station STRONG NULL end points at station NULL Seen from above: a figure 8. 3. Antenna and tuner in one tuning capacitor (the dial) first transistor main coil + capacitor tune the station small winding feeds the transistor about 250 µH tunes down to 530 kHz

The loopstick in three pictures. The ferrite rod gathers the magnetic half of the radio wave through its coil (1). It hears best broadside and has sharp nulls off its ends (2). And its coil is also the first tuned circuit of the radio, with a small extra winding feeding the first transistor (3).

Drawing 14.16-2

Sources: radiojayallen.com loop antenna reviews (Select-A-Tenna, Terk AM Advantage, Degen TG39); AA7EE, "A Tuned Loop Antenna for the AM Broadcast Band"; RADIO-TIMETRAVELLER ferrite loopstick series; Arcane Radio Trivia, "Inductive Coupling and the Select-A-Tenna."

Sources for the loopstick section: Silicon Chip, “Those Mysterious Antenna Coils and Loop Antennas” (November 2008) and “Improving AM Broadcast Reception” (January 1999); RADIO-TIMETRAVELLER, “The Unassuming Antenna: The Ferrite Loopstick” (January 2011); TDK, “Ferrite World”; SWLing Post, rotatable AM antennas and rotating ferrite antenna reports (2016 and 2021); IRCA mailing list archive at hard-core-dx.com (loop and ferrite rod nulls); All About Circuits and RadioReference forum discussions of ferrite rod antennas; cool386.com reflex receiver notes (coupling winding to the transistor base). The 250 microhenry figure is calculated from the standard tuning formula.

© 2026 Chris, N6JET. Free to read and share for non-commercial use with credit (Creative Commons BY-NC 4.0). Not for sale.

More in The Listener's Side: Receivers and DXing

All AM radio stories by subject · AM radio interactive tools and simulators · AM Trivia Challenge quiz