Chapter 3, Section 5

Throwing the Switch at Sunset and Sunrise: When the Pattern Changed by Hand

Part of AM Radio Facts and Trivia: The AM Broadcast Band in the USA. Updated November 16, 2026.

A directional AM station leads a double life. By day its towers throw one pattern; at sunset, to keep its nighttime skywave from smashing into distant co-channel stations, it must change to a different pattern (usually a tighter one, often at lower power) and then change back at sunrise (see The Daytime-Only Era and Pre-Sunrise & Post-Sunset Authority for why the clock matters). Today that swap happens by itself: a timer or the remote control fires a bank of heavy RF relays that go ka-chunk while the transmitter blinks off and back on. But for the first few decades of directional broadcasting, the pattern didn't change by itself. A human changed it, by hand, twice a day, every day.

The machine in the middle. The heart of a directional array is the phasor, a cabinet full of capacitors and variable inductors that does two jobs: it divides the transmitter's power among the towers, and it delays the current to each tower by a precise amount. Those amplitude-and-phase relationships are what bend the signal into the licensed shape. A second pattern means a second set of values: different power division, different phase angles, and often different settings in the antenna tuning units (ATUs) out at the base of each tower. Changing patterns meant physically moving the array from one set of values to the other.

Try it yourself: the AM Phasor Simulator, running right here on the page.

Tool 3.5-1

By hand, with a logbook and a crank. In the manual era the phasor was a wall of knife switches and hand-cranked controls, roller inductors and variometers (variable coils) and big air-spaced variable capacitors, each with a dial. The engineer kept a logged set of positions: one column for day, one for night. Twice a day the ritual ran: at the FCC-defined local sunset, and again in reverse at sunrise. At sunset: drop the transmitter's power, throw the changeover switches to bring the night network into the circuit, crank each variometer and capacitor to its logged night position, bring the power back up, then walk to the antenna monitor and confirm the phase and current-ratio readings for every tower fell inside the license. If a reading was off, you cranked until it came in. At sunrise you did the whole thing again, the other way.

The danger. This was not flipping a light switch. The phasor and the tuning units carry the entire output of the transmitter: on a 5 to 50 kW station that means high RF current and several thousand volts of RF sitting on the coils, the capacitor plates, and the switch jaws. Three ways it could hurt you:

And all of this got done twice a day, including at a bleary local sunrise, often by one person, alone, in a small building out in a field. The procedure (power down, switch cold, ground it, then touch it) wasn't bureaucratic caution. It was the difference between a routine changeover and a very bad morning.

The changeover, by hand: at sunset, and again in reverse at sunrise
1. Reduce transmitter power (or switch off), never switch RF under full power
2. Throw the knife switches / changeover bars to the night network (day network at sunrise)
3. Crank each variometer and variable capacitor to its logged "night" position ("day" at sunrise)
4. Bring power back up to the licensed level for that part of the day
5. Read the antenna monitor: verify phase and current ratio for every tower
6. Adjust until every reading is within the licensed tolerance, then log it

Table 3.5-2

The changeover by hand, at the phasor cabinet (numbers match Table 3.5-2)PHASOR CABINETDNDNDNKnife switches: day / night network2VariometerCapacitorVariometerCapacitorCrank each to its logged position3Each crank and dialhas a day and anight settingLogbook (example values)ControlDayNightVariometer A4762Capacitor A1831Variometer B5540Capacitor B22273Transmitterpower down first, back up last14Antenna monitorphase and current ratiofor every tower56The danger: why the order matteredArcSwitching with power up draws ablue-white arc that welds contactsand starts fires: switch it cold.RF burnRF cooks deep from the inside,often before you feel it.Stored chargeKill the plate voltage, then touchevery node with a groundingstick before a hand goes in.At sunrise the engineer did it all again, the other way, often alone in a building out in a field.

Drawing 3.5-3

Enter the motor. The hand-crank era ended not with a rule change but with hardware. Motor-driven variometers, preset taps, and banks of RF contactors (relays heavy enough to carry the array's current) let the whole day/night swap be triggered by a single control instead of a sweating engineer with a logbook. Once the change was a switch closure, it could be thrown from the studio over the remote control (authorized for directional stations in 1957), and eventually fired automatically on a clock. The modern descendant is exactly what you hear on a tour of a working directional site: a dozen or more massive relays slamming over in sequence with that signature ka-chunk ka-chunk, the transmitter ducking for a half-second, and the pattern reshaping itself with nobody in the building.

The trivia. A 1960s phasor and a 2020s phasor do the same physics with the same kinds of parts: coils, capacitors, and a common-point match. The difference isn't the network; it's who turns the knobs, and at what risk. For the array's first decades that was a person, on site at sunrise and sunset, reaching into a cabinet full of high-voltage RF and reading dials by the glow of the meters. Now the relays do it on a timer, and the only thing that remembers the old ritual is the ka-chunk.

Sources: Radio World (Mark Persons, "Best Practices for AM Directional Systems"; "Digital Phasor for AM Directionals") · Jeff Geerling / Hackaday (WSDZ phasor site tour) · Wikipedia (Phasor (radio broadcasting); Knife switch; RF burn).

© 2026 Chris, N6JET. Free to read and share for non-commercial use with credit (Creative Commons BY-NC 4.0). Not for sale.

More in Directional Arrays and Switching

All AM radio stories by subject · AM radio interactive tools and simulators · AM Trivia Challenge quiz