Chapter 1, Section 3

Ground Loss vs. Frequency: Why Lower on the Dial Goes Farther

Part of AM Radio Facts and Trivia: The AM Broadcast Band in the USA. Updated November 15, 2026.

Here is a puzzle that surprises even experienced operators. Take two AM stations running the identical 5,000 watts into similar towers, one at 600 kHz near the bottom of the dial and one at 1500 kHz near the top. In the daytime, the 600 kHz station reaches significantly farther. Now add the twist: the low-band station's tower is usually the less efficient radiator of the two. So the station with the worse antenna covers more ground. How?

The answer is to separate two things that frequency pulls in opposite directions: how well a station launches its wave, and how well that wave survives the trip across the ground. (This is the daytime groundwave story. A companion section, Groundwave, Skywave & the M3 Map, covers the band's two other great variables: the conductivity of the ground you're transmitting over, and why skywave makes night a different world. This one is about frequency.)

Launch: the high end's advantage. A vertical AM tower radiates most efficiently when it is a useful fraction of a wavelength tall, and wavelength balloons toward the bottom of the band. At 600 kHz a full wavelength is about 500 meters, so a quarter-wave tower, the classic efficient height, would need to stand roughly 410 feet. At 1500 kHz the wavelength is only 200 meters and a quarter-wave is a mere 164 feet. Put the same ordinary 300-foot tower on each:

600 kHz1500 kHz
Wavelength500 m (~1,640 ft)200 m (~656 ft)
A full quarter-wave tower~410 ft~164 ft
A typical 300-ft tower is…0.18 λ (66°), short of quarter-wave0.46 λ (165°), a tall, efficient radiator
Groundwave reach at 5 kWfarthershorter

Table 1.3-1

This is exactly the situation you see on real towers: a 600 kHz tower is often a tall structure that still falls short of a full quarter-wave, while the same height at 1500 kHz is a comfortably efficient radiator. On the launch side alone, the high-band station wins: it gets a few more decibels of signal off the tower. That's the part everyone expects.

Survival: the low end's much larger advantage. Then the wave has to travel. As it drags itself along the ground, the imperfect earth bleeds energy out of it, the wave tilts forward and pours power into the soil as heat, and that loss climbs steeply with frequency. The mechanism is the skin effect in the earth: a higher-frequency wave forces its return currents into a thinner surface layer of ground, raising the effective resistance and burning off the signal faster. So mile after mile, the 1500 kHz wave is absorbed harder than the 600 kHz wave. Crucially, this is not a one-time penalty: it compounds with every mile of the path.

And that is why the low end wins. The high-band station's antenna advantage is a single, modest, few-decibel head start, paid once at the tower. The low-band station's propagation advantage is a lower loss rate that keeps paying off across the entire journey. A small lead at the starting line is no match for running downhill the whole race. By fifty or eighty miles out it isn't close: the 600 kHz groundwave is still usable where the 1500 kHz signal has long since sunk into the noise.

Same 5,000 watts, same ground: how far each signal reaches by day0.010.11101001,0000255075100125150Miles from the towerSignal strength (millivolts per meter)0.5 mV/m: edge of daytime coverage112 miles41 miles600 kHz1500 kHz

Drawing 1.3-1

Both stations run 5,000 watts into towers of the same efficiency (282 millivolts per meter at 1 kilometer for each kilowatt, the FCC minimum for a Class B station), over the same ground (conductivity 8 millisiemens per meter, dielectric constant 15, a middle value for land on the FCC conductivity map). At the tower the two signals start almost even. By 25 miles the 600 kHz signal is about six times stronger, and the 1500 kHz signal crosses the 0.5 mV/m line, the FCC daytime protected contour for a Class B station, at about 41 miles. The 600 kHz signal holds on to about 112 miles. The curves are computed on this site with the standard groundwave method used for the FCC graphs in rule 73.184 and were checked against FCC Graphs 3 (610 kHz) and 18 (1470 kHz), matching within about 5 percent.

Two practical consequences fall out of this. First, it's why stations at the bottom of the band build those enormous towers: they can't easily reach a full quarter-wave (410 feet is a lot of steel), so they go as tall as they practically can to claw back launch efficiency, fighting the one category where the low band is at a disadvantage. (You can watch that field-versus-height tradeoff in Tower Height & Signal Strength.) Even so, a low-band station with a modest, electrically short tower still outdistances an efficient high-band station, because the propagation physics does the heavy lifting, not the antenna. Second, frequency is only half of the survival story: the ground the wave crosses matters just as much, which is the conductivity tale told in the M3 map section. Put the two together (a low frequency over high-conductivity ground) and you get the booming daytime signals that punch far out of proportion to their power.

So the rule of thumb that low-dial stations "boom in" while high-dial stations stay local isn't folklore; it's the attenuation curve of the earth itself. Lower frequency means lower ground loss means farther daytime reach, and that single fact outweighs antenna efficiency, tower height, and nearly everything else about how far a daytime AM signal will go.

Sources: Wikipedia (Ground wave) · FCC M3 Ground Conductivity Map and AM Groundwave Field-Strength Graphs (47 CFR 73.183/73.184) · ITU-R groundwave propagation curves.

© 2026 Chris, N6JET. Free to read and share for non-commercial use with credit (Creative Commons BY-NC 4.0). Not for sale.

More in The Physics of AM

All AM radio stories by subject · AM radio interactive tools and simulators · AM Trivia Challenge quiz